Skip to topic | Skip to bottom

Start of topic | Skip to actions


FAQ | SW: Handling AMR | SW: Handling trig and tet meshes | SW: Tools: VisIt Tutorial | SW: Tools: VisIt Scripting | SW: Tools: Paraview Tutorial

Currently the VTF project at Caltech endorses only two off-the-shelf packages: VisIt and Paraview. The goal is to use these packages for interactive visualization and analisys of data resulting from VTF coupled simulations. This mostly means AMR meshes as well as unstructured triangle and tetrahedronal meshes.


AMR visualization is focused on data resulting from AMROC simulations. Data resulting from AMROC is by default written in HDF4 format. In order to be able to be fed into either Paraview or VisIt it needs to be first preprocesses.

AMROC HDF4 to Paraview

The main tool for data conversion in AMROC is called hdf2file. hdf2file currently has four filters which result in the flattening of the level data into a single unstructured mesh. These for formats are:

  • [10] legacy VTK ascii
  • [11] legacy VTK binary
  • [12] VTU (VTK XML) ascii
  • [13] VTU (VTK XML) binary

Binary VTU is currently the best format to use for Paraview. There is a fifth alternative, though it has not been completely carried out due to a major deficiency. The Paraview PVD format is a collection format which can point to a series of structured blocks, and even append some meta information such as level. However, each of these blocks it points to must be a separate file. So, in order to dump a generally medium size AMR mesh into ![14] PVD it would require hundreds to thousands of files for each structured subblock. This may change in the future.


The main tool for data conversion in AMROC is called hdf2file. hdf2file currently has two filters which result in the flattening of the level data into a single unstructured mesh. These for formats are:

  • [10] legacy VTK ascii
  • [11] legacy VTK binary
  • [15] legacy SILO binary (structured hierarchical) data

Unfortunatelly these legacy VTK formats cannot store level information, nor do they use the more modern VTK XML formats. Thus the current VTK filters flatten the mesh into an unstructured mesh. Meanwhile, the native LLNL Silo format, dumps all data blocks into a single Silo file. Blocks are then collected in levels, all_levels, and variables. These collections are what are exposed to the user in Visit. To create different collections (for example levels 3 and up), you can do this by manipulating directly the directly. See below, or the official Amroc page, for more info.

Using hdf2file

Using hdf2file after running your VTF (Amroc) simulation is quite simple. All it requires is which describes what variables you will be dumping, and what format. Here is a sample used along with the 3D/Spheres AMROC demo.

    # # sample
    Type  1
    FileType 13
    Keys d,u,v,p,i,s
    DisplayMinLevel    0

FileType describes the output file format. The different available formats are:

hdf2file cheat sheet
0 ) WriteASCIITabular
1 ) WriteASCIITabular
2 ) WriteRegularTabular
3 ) WriteDXFile OpenDX Link
4 ) WriteDXASCIIFile
5 ) WriteDXExternalFilter
6 ) WriteHDFConvert
7 ) WriteHDFConvertReduced
8 ) WriteTecplotASCII Tecplot Link
10) WriteVTKASCIIFile
11) WriteVTKFile Visit Link
12) WriteVTUASCIIFile VTK Link
13) WriteVTUFile Paraview Link
14) WritePVTFile Paraview Link
15) WriteSILOFile Visit Link

Type describes whether to dump cell data (0) or vertex data (6). Notice that even though both Paraview and VisIt can handle cell data, some ghost-cells might dump NANs. The conversion (actual conversion happens in hdf2file) to vertex data will most likely clean this up and make either tool run in a more stable fashion.

After you have your setup, then you can run hdf2file. A sample execution of hdf2file:

hdf2file -m -f -fs > spheres.01.vtu


Thin shells modeled as 3d triangle meshes, as well as more complex polycrystal models made up as tetrahedronal meshes have a simple direct conversion into VTK formats. There are a couple of VTU filters for these meshes written by Santiago Lombeyda within the VTF repository.

One single filter called tec2file is now available, which can convert a series of ASCII Tecplot files into a single VTU (ascii or binary vtk xml) or legacy VTK (ascii or binary). Notice the legacy binary format is the most compact and most compatible across different visualization software.

Its use is fairly simple. For instance, on asap, for a collection of triangle mesh pieces for one frame (triangles versus tetrahedra need to be flagged explicitly), you would do:

tec2file -tectrigs -readsequence /home/ralf/TubeThin/result-\*-06000.tec -vtk > TubeThin.06000.vtk

For more info see the FAQ. There is also a quick explanation on some of the OtherVizFilters.


Both VisIt and Paraview were designed to work in parallel. Visit runs in parallel through the use of profiles. Paraview gets executed in parallel from the command line using mpirun or starting each component manually.

For more details on using either package see the quick tutorials on:

You are here: Visualization > WebHome

to top

Copyright © 1997-2024 California Institute of Technology.